View HA-5114883_577289.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HA-5114/883
July 1994
Quad, Low Noise, High Performance Uncompensated Operational Amplifier
Description
Low noise and high performance are key words describing the quad, uncompensated HA-5114/883. This general purpose amplifier offers an array of dynamic specifications including 12V/s slew rate (min), and 40MHz gain-bandwidth-product for AVCL 10. Complementing these outstanding parameters is a very low noise specification of 6nV/Hz at 1kHz (max). Fabricated using the Intersil standard high frequency D.I. process, these operational amplifiers also offer excellent input specifications such as 2.5mV (max) offset voltage and 75nA (max) offset current. Complementing these specifications are 100dB (min) open loop gain and 55dB channel separation (min). Economically, HA-5114/883 also consumes a very modest amount of power (225mW/ package), while also saving board space and cost. This impressive combination of features make this amplifier ideally suited for designs ranging from audio amplifiers and active filters to the most demanding signal conditioning and instrumentation circuits.
Features
* This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. * Low Input Noise Voltage Density at 1kHz. . . 6nV/Hz(Max) 4.3nV/Hz (Typ) * High Slew Rate . . . . . . . . . . . . . . . . . . . . . . 12V/s (Min) 20V/s (Typ) * Wide Gain Bandwidth Product (AVCL 10). . . 40MHz (Typ) * High Open Loop Gain (Full Temp) . . . . . 100kV/V (Min) 250kV/V (Typ) * High CMRR, PSRR (Full Temp) . . . . . . . . . . . 86dB (Min) 100dB (Typ) * Low Offset Voltage Drift . . . . . . . . . . . . . . 3V/oC (Typ) * No Crossover Distortion * Standard Quad Pinout
Applications
* High Quality Audio Preamplifiers * High Q Active Filters * Low Noise Function Generators * Low Distortion Oscillators * Low Noise Comparators
Ordering Information
PART NUMBER HA1-5114/883 HA4-5114/883 TEMPERATURE RANGE -55oC -55oC to to +125oC +125oC PACKAGE 14 Lead CerDIP 20 Lead Ceramic LCC
Pinouts
HA-5114/883 (CERDIP) TOP VIEW
-IN1
HA-5114/883 (CLCC) TOP VIEW
OUT 1 OUT 4 -IN4 18 +IN4 +1 -+ 4 17 NC 16 V+9 -IN2 2 3 -+ 15 NC 14 +IN3 10 11 12 13 OUT 2 OUT 3 -IN3 NC NC 1
OUT 1 -IN1 +IN1 V+ +IN2 -IN2 OUT 2
1 2 3 4 5 6 7 + 3 1 + 4+
14 OUT 4 13 -IN4 +IN1 12 +IN4 11 V10 +IN3 9 8 -IN3 OUT 3 NC V+ NC +IN2 4 5 6 7 8
3
2
20 19
+2 -
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207 | Copyright (c) Intersil Corporation 1999
File Number
3-124
511015-883 File Number 3712
Specifications HA-5114/883
Absolute Maximum Ratings
Voltage between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . . 40V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V Voltage at Either Input Terminal . . . . . . . . . . . . . . . . . . . . . . V+ to VPeak Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indefinite (One Amplifier Shorted to Ground) Junction Temperature (TJ) . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC Storage Temperature Range . . . . . . . . . . . . . . . . . -65oC to +150oC ESD Rating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <2000V Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC
Thermal Information
Thermal Resistance JA JC CerDIP Package . . . . . . . . . . . . . . . . . . . 75oC/W 20oC/W Ceramic LCC Package . . . . . . . . . . . . . . 65oC/W 15oC/W Package Power Dissipation Limit at +75oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.33W Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.54W Package Power Dissipation Derating Factor Above +75oC CerDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3mW/oC Ceramic LCC Package . . . . . . . . . . . . . . . . . . . . . . . . 15.4mW/oC
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Operating Conditions
Operating Temperature Range . . . . . . . . . . . . . . . . -55oC to +125oC Operating Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 5V to 15V VINCM 1/2 (V+ - V-) RL 2k
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: VSUPPLY = 15V, RSOURCE = 100, RLOAD = 500k, VOUT = 0V, Unless Otherwise Specified. GROUP A SUBGROUPS 1 2, 3 Input Bias Current +IB VCM = 0V, +RS = 10k, -RS = 100 VCM = 0V, +RS = 100, -RS = 10k VCM = 0V, +RS = 10k, -RS = 10k V+ = +3V, V- = -27V 1 2, 3 1 2, 3 1 2, 3 1 2, 3 -CMR V+ = +27V, V- = -3V 1 2, 3 Large Signal Voltage Gain +AVOL VOUT = 0V and +10V, RL = 2k VOUT = 0V and -10V, RL = 2k VCM = +5V, V+ = +10V, V- = -20V, VOUT = -5V VCM = -5V, V+ = +20V, V- = -10V, VOUT = +5V 4 5, 6 4 5, 6 1 2, 3 1 2, 3 LIMITS TEMPERATURE +25oC +125oC, -55oC MIN -2.5 -3.0 -200 -325 -200 -325 -75 -125 +12 +12 100 100 100 100 86 86 86 86 MAX 2.5 3.0 200 325 200 325 75 125 -12 -12 UNITS mV mV nA nA nA nA nA nA V V V V kV/V kV/V kV/V kV/V dB dB dB dB
PARAMETERS Input Offset Voltage
SYMBOL VIO
CONDITIONS VCM = 0V
+25oC +125oC, -55oC
-IB
+25oC +125oC, -55oC
Input Offset Current
IIO
+25oC +125oC, -55oC
Common Mode Range
+CMR
+25oC +125oC, -55oC
+25oC +125oC, -55oC
+25oC +125oC, -55oC
-AVOL
+25oC +125oC, -55oC
Common Mode Rejection Ratio
+CMRR
+25oC +125oC, -55oC
-CMRR
+25oC +125oC, -55oC
Spec Number 3-125
511015-883
Specifications HA-5114/883
TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: VSUPPLY = 15V, RSOURCE = 100, RLOAD = 500k, VOUT = 0V, Unless Otherwise Specified. GROUP A SUBGROUPS 1 2, 3 -VOUT1 RL = 2k 1 2, 3 +VOUT2 RL = 10k 1 2, 3 -VOUT2 RL = 10k 1 2, 3 Output Current +IOUT VOUT = -5V 1 2, 3 -IOUT VOUT = +5V 1 2, 3 Quiescent Power Supply Current +ICC VOUT = 0V, IOUT = 0mA 1 2, 3 -ICC VOUT = 0V, IOUT = 0mA 1 2, 3 Power Supply Rejection Ratio +PSRR VSUP = 10V, V+ = +10V, V- = -15V V+ = +20V, V- = -15V VSUP = 10V, V+ = +15V, V- = -10V V+ = +15V, V- = -20V 1 2, 3 1 2, 3 LIMITS TEMPERATURE +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC +25oC +125oC, -55oC MIN 10 10 12 12 10 10 -6.5 -7.5 86 86 86 86 MAX -10 -10 -12 -12 -10 -10 6.5 7.5 UNITS V V V V V V V V mA mA mA mA mA mA mA mA dB dB dB dB
PARAMETERS Output Voltage Swing
SYMBOL +VOUT1
CONDITIONS RL = 2k
-PSRR
TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Table 2 Intentionally Left Blank. See AC Parameters in Table 3
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS Device Characterized at: VSUPPLY = 15V, RLOAD = 2k, CLOAD = 50pF, AVCL = 10V/V, Unless Otherwise Specified. LIMITS PARAMETERS Differential Input Resistance Input Noise Voltage Input Noise Current Gain Bandwidth Product SYMBOL RIN EN IN GBWP CONDITIONS VCM = 0V RS = 20, fO = 1000Hz RS = 2M, fO = 1000Hz VO = 200mV, fO = 30kHz VO = 200mV, fO = 1MHz NOTES 1 1 1 1 1 TEMPERATURE +25oC +25oC +25oC +25oC +25oC MIN 250 34 40 MAX 6 3 UNITS k nV/Hz pA/Hz MHz MHz
Spec Number 3-126
511015-883
Specifications HA-5114/883
TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Characterized at: VSUPPLY = 15V, RLOAD = 2k, CLOAD = 50pF, AVCL = 10V/V, Unless Otherwise Specified. LIMITS PARAMETERS Slew Rate SYMBOL +SR -SR Full Power Bandwidth Minimum Closed Loop Stable Gain Rise and Fall Time FPBW CLSG tR tF Overshoot +OS -OS Output Resistance Quiescent Power Consumption Channel Separation ROUT PC CS CONDITIONS VOUT = -5V to +5V VOUT = +5V to -5V VPEAK = 10V RL = 2k, CL = 50pF VOUT = 0V to +200mV VOUT = 0V to -200mV VOUT = 0V to +200mV VOUT = 0V to -200mV Open Loop VOUT = 0V, IOUT = 0mA RS = 1k, AVCL = 100V/V, VIN = 100mVPEAK at 10kHz Referred to Input NOTES 1 1 1, 2 1 1, 4 1, 4 1 1 1 1, 3 1 TEMPERATURE +25oC +25oC +25oC -55oC to +125oC MIN 12 12 191 10 55 MAX 100 100 40 40 270 225 UNITS V/s V/s kHz V/V ns ns % % mW dB
+25oC +25oC +25oC +25oC +25oC -55oC to +125oC
+25oC
NOTES: 1. Parameters listed in Table 3 are controlled via design or process parameters and are not directly tested at final production. These parameters are lab characterized upon initial design release, or upon design changes. These parameters are guaranteed by characterization based upon data from multiple production runs which reflect lot to lot and within lot variation. 2. Full Power Bandwidth guarantee based on Slew Rate measurement using FPBW = Slew Rate/(2VPEAK). 3. Quiescent Power Consumption based upon Quiescent Supply Current test maximum. (No load on outputs.). 4. Measured between 10% and 90% points.
TABLE 4. ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS Interim Electrical Parameters (Pre Burn-In) Final Electrical Test Parameters Group A Test Requirements Groups C and D Endpoints NOTE: 1. PDA applies to Subgroup 1 only. SUBGROUPS (SEE TABLE 1) 1 1 (Note 1), 2, 3, 4, 5, 6 1, 2, 3, 4, 5, 6 1
Spec Number 3-127
511015-883
HA-5114/883 Die Characteristics
DIE DIMENSIONS: 99.6 x 95.3 x 19 mils 1 mils 2530 x 2420 x 483m 25.4m METALLIZATION: Type: Al, 1% Cu Thickness: 16kA 2kA GLASSIVATION: Type: Nitride (Si3N4) over Silox (SiO2, 5% Phos.) Silox Thickness: 12kA 2kA Nitride Thickness: 3.5kA 1.5kA WORST CASE CURRENT DENSITY: 1.43 x 105A/cm2 at 10mA SUBSTRATE POTENTIAL (Powered Up): Unbiased TRANSISTOR COUNT: 175 PROCESS: Bipolar Dielectric Isolation
Metallization Mask Layout
HA-5114/883
+IN2 V+ +IN1
-IN2
-IN1
OUT2
OUT1
OUT3
OUT4
-IN3
-IN4
+IN3
V-
+IN4
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
Spec Number 3-128
511015-883

▲Up To Search▲

Price & Availability of HA-5114883

	To Download HA-5114883 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .